CipherLab 1502 Spezifikationen PDF herunterladen (Seite 73)

Update

Chapter 3

Changing Symbology Settings

3.2.2 VERIFY CHECK DIGIT

Decide whether to verify the check digit. If incorrect, the barcode will not be accepted.

Verify Industrial 25

Check Digit

*Do Not Verify

3.2.3 TRANSMIT CHECK DIGIT

Decide whether to include the check digit in the data being transmitted.

*Transmit

ndustrial 25

Check Digit

Do Not Transmit

1 2 ... 68 69 70 71 72 73 74 75 76 77 78 ... 173 174

1500/1502 Barcode Scanne 1
IMPORTANT NOTICES 3
RELEASE NOTES 5
CONTENTS 9
INTRODUCTION 15
SYMBOLOGIES SUPPORTED 17
QUICK START 19
ENTER CONFIGURATION MODE 20
EXIT CONFIGURATION MODE 20
Quick Start 21
 Refer to Appendix III 25
LIST THE CURRENT SETTINGS 26
ONE-SCAN SETUP BARCODES 28
Chapter 1 29
Chapter 1 31
1.4.2 GOOD READ BEEP 32
1.5 SEND “NR” TO HOST 33
1.6 SCAN MODES 34
1.6.6 ALTERNATE MODE 37
1.6.7 AIMING MODE 37
1.6.8 MULTI-BARCODE MODE 38
1.8 DELAY BETWEEN RE-READ 40
 Continuous mode 40
 Auto Power Off mode 40
 Alternate mode 40
Addon Security Level 42
1.12 NEGATIVE BARCODES 44
1.13 EFFECTIVE DECODING AREA 45
1.13.1 POSITIONING WINDOW 45
1.13.2 ADJUSTING WINDOW 46
Chapter 2 47
2.1 KEYBOARD WEDGE 48
Chapter 2 49
Selecting Output Interface 49
*Capital Lock OFF 54
2.1.3 INTER-CHARACTER DELAY 58
2.1.4 INTER-FUNCTION DELAY 58
2.2 RS-232 59
2.2.2 BAUD RATE 59
2.2.3 DATA BITS 60
2.2.4 PARITY 60
2.2.5 STOP BIT 60
2.2.6 FLOW CONTROL 61
2.2.7 INTER-CHARACTER DELAY 62
2.2.8 INTER-FUNCTION DELAY 62
2.2.9 ACK/NAK TIMEOUT 63
2.3 WAND EMULATION 64
2.3.2 NORMAL STATE 64
2.3.3 BAR STATE 64
2.3.4 MODULE TIME 65
2.3.5 MARGIN TIME 66
2.3.6 OUTPUT FORMAT 67
Chapter 3 69
3.1 CODABAR 70
3.1.1 SECURITY LEVEL 70
3.1.4 CLSI CONVERSION 71
3.2 CODE 25 – INDUSTRIAL 25 72
3.2.2 VERIFY CHECK DIGIT 73
3.2.3 TRANSMIT CHECK DIGIT 73
3.3 CODE 25 – INTERLEAVED 25 75
3.3.2 VERIFY CHECK DIGIT 76
3.3.3 TRANSMIT CHECK DIGIT 76
3.4 CODE 25 – MATRIX 25 78
3.4.2 VERIFY CHECK DIGIT 79
3.4.3 TRANSMIT CHECK DIGIT 79
3.5 CODE 39 81
3.5.2 VERIFY CHECK DIGIT 81
3.5.3 TRANSMIT CHECK DIGIT 82
3.5.5 SECURITY LEVEL 82
3.6 CODE 93 83
3.7 CODE 128 83
3.7.1 SECURITY LEVEL 83
3.8 EAN-8 84
3.8.1 CONVERT TO EAN-13 85
3.8.2 TRANSMIT CHECK DIGIT 85
3.8.3 CONVERSION FORMAT 85
3.9 EAN-13 86
3.9.1 CONVERT TO ISBN 87
3.9.2 CONVERT TO ISSN 87
3.9.3 TRANSMIT CHECK DIGIT 87
3.9.4 SECURITY LEVEL 88
*Disable 90
3.10 GS1-128 (EAN-128) 91
3.10.1 TRANSMIT CODE ID 91
3.10.3 GS1 FORMATTING 92
3.10.4 APPLICATION ID MARK 92
3.12 MSI 94
3.12.1 VERIFY CHECK DIGIT 94
3.12.2 TRANSMIT CHECK DIGIT 94
3.13 FRENCH PHARMACODE 96
3.13.1 TRANSMIT CHECK DIGIT 96
3.14 ITALIAN PHARMACODE 97
3.14.1 TRANSMIT CHECK DIGIT 97
3.15 PLESSEY 98
3.15.1 CONVERT TO UK PLESSEY 98
3.15.2 TRANSMIT CHECK DIGIT 98
Chapter 3 101
Changing Symbology Settings 101
 GS1 DataBar Expanded 102
3.16.6 GS1 FORMATTING 104
3.16.7 APPLICATION ID MARK 104
3.17 TELEPEN 105
3.18 UPC-A 106
3.18.3 TRANSMIT CHECK DIGIT 107
3.18.1 CONVERT TO EAN-13 107
3.19 UPC-E 108
3.19.4 TRANSMIT CHECK DIGIT 110
Chapter 4 111
Chapter 4 113
Defining Output Format 113
4.4.2 CHANGE CODE ID 123
4.4.3 CLEAR CODE ID SETTINGS 124
4.5 LENGTH CODE 125
4.6 MULTI-BARCODE EDITOR 129
 Code Type 129
Enter Setup 132
Remove Special 132
Character 132
Chapter 5 133
5.1.2 EXCLUSIVE DATA EDITING 135
End Programming Format 136
5.2.2 RESTORE DEFAULT FORMAT 138
5.3.1 APPLICABLE CODE TYPE 139
131 145
5.3.2 DATA LENGTH 146
5.4.3 TOTAL NUMBER OF FIELDS 149
5.4.4 FIELD SETTINGS 150
Field 3 Setting 152
139 153
Field 4 Setting 153
Field 5 Setting 154
141 155
Additional Fields 155
Key Type Key Status 155
5.4.5 PAUSE FIELD SETTING 156
5.6 PROGRAMMING EXAMPLES 159
5.6.1 EXAMPLE I 159
SPECIFICATIONS 161
Resistance 162
Programming Support 162
Appendix I 163
Appendix II 165
Appendix III 167
KEY TYPE & STATUS 168
KEY TYPE 168
KEY STATUS 168
EXAMPLE 169
Appendix IV 171
HEXADECIMAL SYSTEM 172
ASCII TABLE 173

Kommentare zu diesen Handbüchern

Keine Kommentare

CipherLab 1502 Spezifikationen Seite 73

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Barcodeleser CipherLab 1502